- WRX
- STI
- BRZ
- FORESTER
FT-86 SpeedFactory
FT-86 SpeedFactory Tungsten Ceramic Coated Catted UEL Header
2013-2022 Scion FR-S / Subaru BRZ / Toyota GR86
$ 1350$1,350.00Ships for free in the 48 states
SKU: FT86CTDHDR-GRYWe price match!
FT-86 SpeedFactory's Catted UEL header is ready to get rid of that notorious torque dip that plagues the Scion FR-S and Subaru BRZ. Made in the USA from 304 Stainless steel and tig welded at every corner then a powder coated finish to finish it off.
The exhaust runners are 1.75" in OD and flow into a 4 to 1 merge collector that exits into a 2.5" OD catalytic converter which mates to the factory over pipe or any aftermarket over pipe that is in the factory location.
Please contact us for current delivery times if the item does not show "IN STOCK"
Note: These have been tested to fit the new 2022 Subaru BRZ and Toyota GR86Details
FT-86 SpeedFactory Catted Unequal Length Header
FT-86 SpeedFactory's Catted UEL header is ready to get rid of that notorious torque dip that plagues the Scion FR-S and Subaru BRZ. Made in the USA from 304 Stainless steel and tig welded at every corner then a powder coated finish to finish it off..
The exhaust runners are 1.75" in OD and flow into a 4 to 1 merge collector that exits into a 2.5" OD catalytic converter which mates to the factory over pipe or any aftermarket over pipe that is in the factory location.
The stock under tray will bolt right back up after installation, making sure you can still protect the cars underbelly, as well.
Quality Improvement
Our catted UEL header is a simple bolt on install that gains 18ft lb. of torque and 12HP in the infamous "dip". Peak power is up 14HP and 5ft lbs of torque with no ECU tuning. Unlock even more with a tune. No CEL, as well, for those who wish to not stare at a light on the dash. No CEL is on a stock car with no other mods. If you have other parts you still need a tune.
Weight
Stock Header = 20.8lbs
FT86SF UEL = 13.0lbsEach header is built to order. Due to the hand made nature of this header lead times can vary depending on current work load. Current lead time is 1-2 weeks if status shows "ships from factory". We do our best to stick as close as possible to these dates.
Please contact us for current delivery times if the item does not show "IN STOCK".
Includes
- OEM Subaru Metal 2.5" Gasket for Overpipe section
- Two Bolts and nuts.
- Lifetime Warranty (original owner only) against cracks or other defects in metal and weld quality. The CAT is void of any warranty claims as this unit can be damaged from HIGH EGT's on bad tunes.
Everyday Driver Video
The guys at Everyday driver are up at altitude for this video (~4500 ft). They run a baseline dyno on their FR-S and then install an FT-86 SpeedFactory catted header and V1 catback exhaust. Includes before and after dyno / drive commentary.
4 customer reviews
-
Excellent
By Jerm September 18, 2022Just installed, noticeable difference in the torque dip just installing these headers and nothing else yet. Isn't gone completely, but very noticeable. Removing stock manifold was definitely the most difficult part, once nuts are loose it's hard to get them off the overpipe section especially. These new headers fit absolutely perfectly, was super simple putting them up. There are a couple nuts hard to get to, need a 3/8" swivel drive and deep 14mm socket and you're good. Also will need a 6" extension for 3/8" drive, 10mm and 12mm sockets to remove panel, and lastly need 15mm socket and 15mm wrench for the over pipe connection replacement nuts and bolts, which come with the headers. Also has all replacement gaskets. Very satisfied.
-
Very satisfied
By LW May 20, 2022This is a very well made header and it sounds amazing. Very simple to instal and came with all the gaskets and new bolts. Very noticeable difference I also am running a stage 2 tune with it.
-
Great!
By Silvester787 April 17, 2022Had absolutely stock 2017 BRZ 6 speed manual, complete with the famous BRZ mid-range torque dip. Very annoying. Installed the UEL catted header and open flash stage 2 tune. Stock exhaust system was retained. As advertised the torque dip was improved dramatically if not eliminated entirely. The car is much more enjoyable to drive and performs as one would have expected originally, like a real sports car albeit not a muscle car. You'll need a blower for that... The installation was easier than I expected. I had no issues with the original exhaust hardware. Viewing YouTube installation videos was helpful. The fit was absolutely perfect. This is a very high quality piece. Excellent craftmanship and finish. 100% satisfied with the results.
-
Easiest aftermarket install I've ever done!
By J-Boogie April 1, 2021I can't say it enough... these headers fit perfectly, they sound great, and they look great. Sadly you can't really see them. The worst part of the install was getting the factory manifold off. I broke a bolt that connects the stock exhaust manifold to the over pipe. For the new header it was tricky getting to two of the nuts that attached the header to the block but with a swivel adapter it went perfect. The short and sweet of it all is these headers are great! Customer service is awesome as well! Thanks guys!
QUESTIONS & ANSWERS
No questions have been asked about this product.Upload images for this product
© 2014 Subispeed. Powered by JB Autosports.
- STI
