SubiSpeed Facelift JDM Style DRL Bezel
Subaru didn't bring these awesome fog light bezels to the states. They can be imported but at a cost. A similar look can be replicated using these SubiSpeed bezels however. They feature metallic gloss black bezels and an ultra bright DRL strip.
This version also adds a little more functionality over the JDM bezel. They have full sequential turn signals built in. You can change the function from sequential to standard blink with the flick of a switch on each side.
Subispeed's How To Install Video
This video for the original DRL bezels is a great start for your installation. The only added item for these are the pass through turn signal plugs which were designed for vehicles with the turn signals mounted in the lower fog light area. If you vehicle is equipped with headlights which house your original turn signals, you will need to tap those wires into the bezels.
NOTE: These bezels DO NOT have separate LED driver boxes. The electronics are all integrated into the light housing.
- Red - Positive
- White - DRL Override (positive, connect to power wire IF you want it to turn off under certain conditions)
- Black - Negative / Ground
- Turn signal pass through harness
You can wire these up a few different ways. If you own a 15-17 WRX / STI with bumper conversion or 18+ WRX Premium / Base owner, we recommend the SubiSpeed Quick Connect wire that goes in your low beam and high beam fuse spots. 18+ WRX Limited and STI owners we recommend modifying an add a fuse plug. More details on the "additional" tab.NOTE: While most of the connectors are sealed, DO NOT allow connectors or the driver boxes to rest in areas where water pools up (ie the plastic tray at the bottom of the car). Encouraging them to be submerged in water for periods of time is not recommended for long life. Mount them in an area that will minimize exposure to water and vibration.
DRL Turn Signal Quick Connect Harness
This product comes with a single add a fuse which can be placed in the high beam fuse position in the fuse box. However, it will go off when the headlights are turned on. There is also another location to get accessory power, but it will always be on. If you want the DRL on this bezel to act like a real DRL (ie turns off when the parking brake is up), choose this harness. It will use both the low and high fuse positions in the fuse box.
Turn Signal Quick Connect Harness for Factory LED Equipped Vehicles
The wiring for 18+ LED headlight equipped vehicles is different from their halogen counterparts and even the 15-17 models equipped with LED headlights. The turn signals were moved up into the headlight casing. This poses a small issue for the standard wiring. This turn signal quick connect harness comes with a factory style plug on one end with insulated male terminals on the other. Just crimp the female T-taps over there two wires going to the factory turn signal bulb in you stock housing and connect these wires to it. Also supplied is a factory style block off plug to prevent anything from getting inside the rest of the wire. Comes with a pair of harnesses, plugs, and 4 female t-taps. These are all the items required for one vehicle.
This Part Fits
- 2018+ Subaru STI SubiSpeed Facelift JDM Style Sequential Turn + DRL Bezel
- 2018+ Subaru WRX SubiSpeed Facelift JDM Style Sequential Turn + DRL Bezel
All vehicles can use this solution. The lights will come on when you start your vehicle using this power source. The need for this method comes from the 18+ WRX Limited and 18+ STI models which have their stock DRLs integrated into the LED headlamps.
It requires the use of an add a fuse.
You will want to remove the lower fuse if you have one installed in your add a fuse. The top slot will require a low amperage fuse (below 5 amps). You will want to remove the prong that is circled in the photo below also.
Locate the position of the DRL fuse.
Insert the modified add a fuse just like the picture below. This connection will provide a positive power point for your DRL bezels.
For customers that have turn signals in the lower bumper already, a pass through harness has been included that will allow for simple plug and play installation. For customers that have turn signals in their factory headlights, you will need to run your own wires and tap into the turn signal positive and negative on each side.
|Additional Warranty Information||None|
Be the first to review this product
Upload images for this product
Feel free to share pictures of your vehicle with this product!